New Carpet

The new carpet was completed after the flood. The guys did a fantastic job making sure all the seams were perfectly aligned. Should last for many, many years.

The Flood

A bit of a setback, but a chance to move forward to something even better. Torrential rains fell last week and the theater was slightly flooded. Only carptet deep, but that means it has to be replaced. The search begins for something new to replace it.

Paragon Butter Warmer

Below is a summary and some pictures/ video of the Paragon Butter warmer with both the old and new container.
I added enough water (2.5 cups) to the inside unit to make the container float. It does wobble when empty. I then added 1 cup of water to the container. No more floating, and plenty steady when pumping.

I then set the thermostat as high as it would go, and put a candy thermometer in the container water. The ambient temp was 70 F. After 4 minutes, the temperature reached 75 F (as low as my thermometer would go). I took readings every 5 minutes for 1 hour. The voltage was 122 VAC, and the unit drew 1.67 Amps (203.75 Watts) as measured by a Kill A Watt EZ P3 gauge.


5 min = 85 F
10 min = 110 F
15 min = 125 F
20 min = 150 F
25 min = 165 F
30 min = 175 F
35 min = 185 F
40 min = 190 F
45 min = 195 F
50 min = 200 F
60 min = 200 F

So far I like the new design, but all I have heated is water. Steam does escape around the outer ring, and the water in the heated section barely reaches a boil at 1 hour which seems reasonable.

The bottle and holder for the original design was begining to rust and the bottle had deformed (bulged) on the bottom and would no longer stand upright without holding.

The new design is much cleaner and easier to work with.

Below is a quick video of the container when inserted empty. In the second video 1 cup of liquid was added to the inner cup making the unit stable with no bobbing and very little movement when pumping. You can also freely rotate the pump in any direction since it is not attached to the container.

Another Update to the 6500UB

Just finished adding the new firmware 1.09 to the Epson 6500UB, along with an improvement to the Frame Interpolation module. The projector is much smoother with FI on LOW now, though I didn't notice any changes to Normal and High. I use LOW for normal TV viewing, and Normal or High for sports and animated dvd's. I still prefer the1080p24 4:4 pull-down for viewing film based material.

Updating the 6500

Finally, an improvement in the HDMI handshaking on the Epson 6500. This projector has been painfully slow when changing resolutions or sources. With firmware 1.08, the handshake time has been reduced to a more manageable time, though still not as speedy as my old AE700. At least not changes can be made to the menu items without having to wait 25 seconds or more for the picture to return.

Some Videos of the 6500

I captured some videos today of the 6500. The first shows the cold startup time. The 6500 had been off all night, the BD-35 was already started and on the main menu screen of Kill Bill 2. The video chain is as follows:
BD-35 --> DVDO Edge --> SR805 --> 6500

The power on occurs approxiamately 5 seconds after the start of the video.



The second video shows the time it takes to start playing "Iron Man" after the projector has been started.





The third video is High an Low lamp, and the auto iris function. The basic idea was to capture the fan noise and shutter noise. Unfortunately, the Pentax Optio A20 has a very poor microphone. The auto color balance of the camera is also quite poor in low lighting, so these videos do not represent the image quality of the 6500.

The Epson 6500UB Arrives

The Epson 6500UB arrived this morning around 10 am. By 10:15 I had it mounted, and by 10:30 I was ready to test it out. So far, so good! No dead pixels, no convergence issues, no stuck focus ring, and no dust blobs. The image is stunning compared to my old Panasonic AE700. So far it has exceeded my expectations in everything but the Frame Interpolation feature is very 'freaky'. It is one of those things you just have to see to understand, as it is difficult to describe in words.

Not only does this projector throw an extremely sharp, and bright image, but it is also quiet in the "Theatre" modes. I am not sure how it compares to the Panasonic AE-3000, but it is only audible in very quiet scenes. In fact, I now can hear the Panasonic BD-35 fan which I didn't hear before. This projector shows every flaw in the source material, dust, scratches, noise, you name it.

The Epson 6500UB is on the way

I got the phone call tonight from AVS, my projector is shipping tomorrow. I am hopeful that it gets here by Friday, but it is difficult to say with NYE holiday. A very good review was posted on Projector Reviews

This will complete the upgrades for the year, and I think I finally have everything in place. I have converted from HD DVD to Blu-Ray, from a 720p to 1080p projector, and upgraded my receiver. I think I can finally relax and not think about any more changes for now.

Onkyo TX-SR805

Decision time is over. I went with the Onkyo TX-SR-805. Should be here sometime next week. Until then, I am without sound...

HK-635 and Panny V2600 GONE!

I am now without a receiver to power my theater. I recently sold both the Harman Kardon and Yamaha receivers. I thought it was time to move up to HDMI 1.3 and the new audio decoders (True-HD, DTS-MA) to use with my BD-35. Perhaps it is time to try another brand, like the Onkyo TX-SR805? It seems to do all the things I want, and without all the video processing that I do not need.

On the Wait List

The decision is over, I went with the Epson 6500UB. I am on the wait list, and the first batch of these projectors should ship out next week. Whether or not I make the cut for the first shipment is still unknown. At best I could have the projector by Dec. 19th. More realistically, it will be mid-January. A lot depends on how many Epson is actually able to ship to the distributors, and how many people are ahead of me on the list.

In the meantime, I can practice taking measurements with HCFR software and the Spider 2 sensor on the old AE-700. The more I practice, the easier it will be to calibrate the Epson when it arrives. If rumors are correct, a similar projector is almost spot on right out of the box

DMP-BD35 Player

Well I finally took a swig of the blu-ray kool-aid, and so far it is not too bad. This weekend Costco was having an $80 off sale on their two BD players (BD-30 and BD-35). I stopped by 3 stores trying to locate the BD-35, but all they had was the BD-30 (which I did not want). At the last store, I had one of the employees look up the sku for the BD-35 and he came back with some interesting news. They did have several of these players, but they would not put them out until all the BD-30's were sold. It seems there was a note that indicated that the BD-35 were meant to be a replacement for the BD-30's so they were not bringing them out. That sort of frosted me, so I thanked the guy for his help and left. When I got home, I grabbed the Costco Connection magazine that had the ad, and headed by to the second store (which had 72 units). There I spoke to another employee, who was very knowledgeable about the BD-35. He knew where they were, but also gave me the same story about having to sell all the BD-30's before they could bring them out. I showed him the ad, and pointed out that the sale specifically mentioned the BD-35. I also explained to him that they had different sku numbers, and even a different price. After a little more small talk, I was able to convience him.

I had to wait 30 minutes or so for the forklift to make it to the far end of the store where the prized BD-35's were sitting in wait. When they were finally lowered, I snatched one up and headed home. I had also picked up a copy of Iron Man in BD to test it out (since they were $5 off). A neighbor and his friend stopped over to give the player its first showing. There was some issue getting the PCM channel working through my receiver, but after about 5 false starts, we finally had full audio. Something still seems a bit odd about that experience, but I didn't have time to figure out what component was at fault.  

The BD-35 is quite nice, from the time I have had to play with it.  It loads fast, has a very nice menu layout, and was easy to update the firmware over the internet (took about 10 minutes to load V 1.5).  It is hooked up through my DVDO Edge, so it is hard to judge the picture quality without bypassing this processor.  Everything seems to look good hooked up through Edge.

This definitely pushes me one step closer to purchasing the 1080p projector. Just need the first user reports to start rolling in on the 6500UB. 

Ceiling Mounting the AE-700

In preparation for the purchase of either an AE-3000 or 6500UB, I have been moving around my 4+ yo AE-700. This past weekend, I purchased a universal mount from Monoprice and moved the AE-700 from ~20 ft (back of room shelf mount) to ~10.5 ft ceiling mount. My screen is 106" High Contrast Cinema Vision (HCCV), a gray screen rated at 1.1 gain, so I am just a tad too close to fill the entire screen. (Oddly it seems to fill horizontally but is a sliver too narrow vertically). This is my first attempt at ceiling mounting and alignment, and I would rather learn on the old than on a brand new one. The learning curve has been steep, but I am finally getting the hang of it and better understand how everything works.

What I have noticed is that the picture is definitely much brighter and has an apparent increase in sharpness. So far I am liking this change in mounting location, and I had someone ask me last night if I had purchased a new projector since it looked so much better. (I know I was stretching it to have the old projector that far from the screen).

Bottom line is that I can wait just a little bit longer now before the upgrade, and I don't think I would ever go back to shelf mount. Hopefully it will be an easy swap out when the new projector gets here.

What will it be: Panny 3000 or Epson 6500

The purchase of a new 1080p projector has been on hold all summer. The two main contenders are the Panasonic AE-3000 and the soon to be released Epson 6500U. The reviews of the 3000 are slowly rolling in, and they are mixed. They have made improvements in brightness and contrast, but it appears they haven't solved the dust blob issue. I have never had a dust blob on my SE-700, so I don't know if I have a cleaner environment, or if it is just luck of the draw.

The 3000 seems to have more user features, like the waveform monitor, zoom memory for 2:35 zooming, and color correction features. Some of these I would use, other features -not so much. If the Epson is quieter, less prone to dust blobs, and has a better brightness and contrast, I may be swayed to go that route. Predictions are that the Epson may be a few hundred more, but no street prices are available yet.

There is also the "Dark Knight" factor. I would like to have the projector installed and calibrated by the second week of December for the 'Dark Knight" movie night. The Epson looks like it will be delayed until around that time frame or longer. That might just be the thing that gets me to confirm the Panny purchase.

Until then, I keep reading and watching as all the information trickles in.

Goodbye 805

Well as much as I loved the Onkyo HD-805, it was no longer needed in the rack. I recently purchased a DVDO Edge video processor, and I have been using that for upconverting SD disks from my Oppo. The REON chip in the 805 did an excellent job, but I was running out of space and trying to make an effort to get rid of redundency. I also was not using the 805 as much as I thought I would, with barely 10 hours of use since I got it.

So what is next? I have been keeping my eye on the Panasonic AE-3000, and so far it looks like the projector for me. I will wait until the first user reports come out, and then purchase it around Christmas. It will make a nice gift to myself.

I was also quite impressed with the PS3 that a couple of my friends brought over last weekend. We watched "The Fall" on Blu-Ray, and it was a very enjoyable movie. Afterwards, we tried some of the games. As much as I hate Sony, this does seem to be a very nice system. Is it worth $399? That is the ultimate question, especially with cheaper standalone BD players coming out. Now if they dropped the price like MS did on the XB360, I might be more tempted.

The MFW-15 Arrives

After many months of pacing the floor, the MFW arrived last Friday. I wasted no time in dragging it down the stairs and ripping it out of the shipping box. I plugged it in, connected it to my system, and listened for the dreaded 60Hz hum. It was there, so I started to track down the source. Without the coax cable connected, the sub was nearly silent so I knew the source of the hum was either coming from the wall power or from the input. A cheater plug was added, and that had a small impact on the hum. As soon as I bypassed the BFD 1124, the hum went away. I had found the source. I added an RS 250-054 line filter to the output of the BFD and once again the hum was eliminated. Problem solved. With the ground loop isolator in place, I ran the Yamaha equalization routine and balance the sub with the rest of the speakers. All was good.

Now came the true test, how would it sound? I popped in my demo discs and ran through the clips one by one. With each clip, the smile grew wider. This is what was missing from my setup, the low end was extremely impressive. The clip of Darla tapping on the fish tank from "Nemo" made the whole room rumble! "Flight of the Phoenix" never sounded more realistic. Musical clips were also impressive, the sub was tight and deep at the same time.

I am very pleased with this sub and look forward to the next Theater Night to show off the new toy!

Deadening the Front Wall

I had a very enjoyable phone call with Bryan from GiK last week. After reviewing my theater layout he made some suggestions.

First, he recommended that the side surrounds be at least 38% of the total room length from the rear wall. With my room being about 20 ft long, that would mean that my rear seating should be around 7 ft from the back wall. Currently I am only at 4 ft. This would take some major adjustment to the seating to make this happen, but I will consider it.

Second, he suggested that all speakers should be set to SMALL, except the mains, with a cross-over of 80 Hz. By doing this, I could use the two Pro-Subs in the rear for the redirected bass and LFE. That may help balance the room once the MFW arrives as I was planning on putting that up front.

Third, he suggested that the front wall should be deadened. We discussed the need for some reflective area directly behind the bi-pole towers (7001's). The reasoning is to absorb any of the center sound that may be bouncing off the front row. This reflection can cause a muddy sound, especially during dialog.

After giving it some consideration, I decided to go half-way and add 2 inch cotton baffles behind the screen. This will absorb much of the reflected sound, but still give the towers some area to bounce. I spend last evening mounting the panels and moving the screen out from the wall by 2 inches. Tonight I will recalibrate the room and see if this was helpful or if it deadened the room too much. The front surface of the screen should allow some reflectance, and the insulation behind the screen will absorb most of the mid-high that passes through. This seemed like a fair compromise to me. A diffuser could be added behind the towers, but that is something for another day. The Tri-Traps should ship the end of this week, and arrive the following week. I plan on placing them in the corners of the rear wall.

The Tri-Traps are Coming!

GiK is having a limited time 10% off sale on their Tri-Traps, making them even more affordable. I picked up a pair to try in the rear corners of my room. I may have to build my own for the front corners because of the limited space I have between the wall and screen.

Theater Layout

I finished the theater layout, just in time to change it all around again. I will be moving all the A/V equipment from the built-in shelving at the rear of the room to the area outside the theater. I am waiting on my 40 ft HDMI cable to get here from Monoprice before I move everything. The projector will stay on the back shelf, but all the other gear will be moved out of the room. When I get around to buying a new projector (after CEDIA), I will mount it on the ceiling behind the rear seating. I am very anxious to see what comes out of Panasonic AE3000? or Epson 1080UB+?

Still waiting anxiously on the MFW-15 sub, and it should be 'coming soon'! At least I have a serial number for it now, just need a shipping invoice and I will be all set!

Scored a pair of BPX's !!

Myer-Emco is having another warehouse sale, so I thought I would at least give them a call to see if they had the BPX surrounds. They don't normally carry them, but when they have their warehouse sale, sometimes the have items that were ordered but never picked up. It was my lucky day, and they had a brand new pair for $249 ea. Now I can finally finish my 7.1 surround system!